Over-Current Protection
Short-Circuit Protection
Over-Temperature Protection
Over-Voltage Protection
*Built-in constant current driver inside the housing
*Every light comes with 2 Meters cable
*Easy to installation.
*OEM service to print your own logo for free
| Model Number | LSL-UDB002-120W |
Total Power | 120W |
| Total Luminous Flux | 9000-10000LM |
| Emitting Color | White |
| Input Voltage | DC10-30V |
| Beam Angle | 60°x90° |
| Power Efficiency | >86% |
| Color Rendering Index(CRI) | Ra>80 |
| Frequency Range | 47-63Hz |
| Power Factor(PF) | ≥0.95 |
| Total Harmonic Distortion(THD) | <15% |
| Working Lifetime | >50,000Hrs |
| IP Rating | IP68 |
| Body Material | 316L Stainless Steel |
| Product Size | 140 x 60 x 13MM (5.51" x 2.36" x 0.51") |
| Net Weight | 0.7KGS (1.54lbs) |
| Gross Weight | 0.8KG (1.76lbs) |
| Inner Box Size | 24.5x12x6.5CM |
| Carton Packing Size | 60x26x17CM (23.62"x10.25"x6.7") 20PCS/CTN |
DIRECT MANUFACTURER CAN PROVIDE YOU MORE COMPETITIVE ADVANTAGES
SMALL ORDER
NO MOQ
FAST DELIVERY
24*7 AFTER SALES SERVICES
YOU MAY LIKE:
1. Lights must be operated on an appropriately fused or circuit breaker protected circuit. Lights are not recommended for mounting on running surfaces (e.g., the bottom surface of a hull) For best performance, lights should be mounted below the waterline.
2. Bottom paint is no required, however lights can be painted with any stainless-safe paint if desired. Light circuits should be protected with an appropriately sized fuse.
3. Mounting surfaces should be flat, clean, dry, and free of any existing hardware or holes. Before mounting ensure that the light will not interfere with the operation of engines, trim tabs, rudders, etc. Ideal mounting locations include transoms, the side and back surfaces of engine brackets, and the undersides of dive platforms. For maximum performance lights should be mounted 6" to 150" below the waterline. Installation at depths greater than 200"is not recommended.
4. Extreme care must be taken when driving screws to prevent screw heads from shearing off. The diameter of the pilot hole required for the mounting screws will depend largely on the composition and thickness of the mounting surface.
5. Size pilot holes so that only moderate torque is needed to drive the screw into the mounting surface. This hole size will be usually smaller than the outside diameter of the widest threads typically. Test the size of the mounting hole prior to installation. Carefully turn screws to avoid breaking them. If screw is too tight, back out and re-size screw hole. When drilling fiberglass, slightly countersinking the hole using a 3-fluke countersink bit will reduce gelcoat chipping.
6. Thoroughly coat the back surface of the light with a marine-grade sealant designed for below waterline applications. Dab additional sealant on the holes in the mounting surface, forcing some sealant into the holes. Extreme care should be taken to properly seal the through-hull (wire) hole to prevent water intrusion.
7. Press the light firmly into place to bed it in the sealant. Tighten the mounting screws evenly. Sealant should be forced from all sides as the light is tightened down. Thread the wire strain relief from inside the boat along the power wire. Press if firmly into the wire hole to properly seal and prevent water intrusion. Allow the sealant to cure thoroughly per the manufacturer's instructions prior to returning the vessel to the water.
1. These underwater led marine lights are designed to mounted to your boats.
Use high power LED on marine to show sea creatures at night, floodlight to
show off the outline of the boat,the illuminative light as new fashion illumination.
Light up the water behind your boat with these super bright high quality underwater
led lights. Amazing looks, Attract marine life, wakeboard on illuminated water.
2.These lights also good for Boat, Yacht, Marine docks, ponds, swimming pools, fountains or any other
underwater lighting application.
